Journal of Engineering Geology

---

This paper has evaluated the groundwater quality index of Lenjanat aquifer. Water quality index as a unique index is presented to describe overall water quality conditions using multiple water quality variables. Physical and chemical data of 66 water samples were used in this study. The results have been obtained by Comparing the qualitative features with the World Health Organization (WHO) standard and Industrial Research of Iran (ISIRI) standards. In calculating GQI, 7 parameters, including calcium (Ca), magnesium (Mg), sodium (Na), chlorine (Cl), sulfate (SO4), total dissolved solids (TDS) and nitrate (NO3) have been used. Groundwater quality index shows the medium to relatively high groundwater quality in the study area. Minimum and maximum value of the index is calculated as respectively 55 and 93. Land use map shows that along the Zayanderood River and around the location of rice paddies, water quality reaches to the lowest quantity. Optimum index factor technique allows the selection of the best combination of parameters dictating the variability of groundwater quality.

---

Several studies show that during and before the earthquake, ground water existing in layers of the earth crust undergoes physical and chemical changes. These changes are recorded by measurement devices and known as "Geohydrological Precursors". Based on the studies conducted in this field, earth electromagnetic field waves experience fluctuations during and even before happening of the earthquake, which are called "magnetic anomalies". This type of anomaly is known as "geomagnetic precursor" within the scope of earthquake knowledge. S, the aim of this study is to assess the feasibility of making a connection between two groups of earthquake precursors (hydrological and geomagnetic precursors). In the present research, a series of tests has been done in order to investigate the effect of magnetic fields on physical and chemical properties of water, including Electrical Conductivity (EC), Total dissolved solids (TDS), Height of Water (HW). The tests were designed and conducted to be used in short-term and middle-term earthquake prediction. Analysis of the experimental results using statistical tests indicates that there is a partial meaningful relationship between magnetic fields (geomagnetic precursor) and physical and chemical properties of water (hydrological precursors), with the confidence coefficient equal to 95 percent

---

Introduction
Every year, numerous casualties and a large deal of financial losses are experienced due to earthquake events. The losses incurred by an earthquake vary depending on local site effect. Some well-known examples include the earthquake in Caracas 1967, Mexico city 1985, Kalamata 1986, Loma Prieta 1989, Roodbar 1990, Bam 2003, Jammu and Kashmir 2005, Sichuan 2008 and Haiti 2010. Therefore, in order to conquer drastic effects of an earthquake, one should evaluate urban districts in terms of the local site effect. Various methods are available for the evaluation of site effect. One of the most common methods includes ambient noise survey. Today, this approach is being used as fast, applicable, cost-effective method. Ambient seismic noise are feeble ground motions with displacement amplitudes of about 0.1–1 μm and that can be detected by seismograph with high magnification. Many investigations have been conducted to determine the nature of ambient noise. One of the possible sources of ambient noise can be human activity, such as traffic, industrial noises and nature activity, such as wind, ocean waves. The Babol city is one of the largest cities in the north of Iran (Mazandaran province). It lies on alluvium beds in the region presenting a high seismic potential. Therefore, comprehensive studies are necessary to introduce suitable solutions for minimizing earthquake damage and loss of life. For this reason, in Babol city, ambient noise survey has been performed at 60 stations and the obtained data were analyzed with Nakamura or H/V method (1989). The results were compared with local geological, geotechnical and seismic data to confirm their reliability for a seismo-stratigraphic.
Methodology and data collection
The analysis of ambient noise was initially proposed by Kanai and Takana (1961). Since then, many researchers have used ambient noise for site effect evaluation. As it is said before, one of the most popular techniques for estimation of site effects in the regions with low seismicity is ambient noise survey by Nakamura or H/V method (1989). Based on the literature review, the Nakamura method (1989) has been used in many places. Many theoretical and experimental studies show that, this method has the capability of estimation of fundamental frequency. Ambient noise survey was carried out at 60 stations in Babol city. Ambient noise was recorded using a velocity meter SARA. Two horizontal and a vertical components of ambient noise at each location are recorded for duration of 15 min with 100 samples per second. Because the environmental noise has an effect on ambient noise they are recoded between 10 p.m. to 6 a.m. The locations were determined by using GPS at the sites. The ambient noise survey in this study was made in compliance with the guidelines of SESAME (2004).
Results and discussion
The maximum and minimum values of fundamental frequency of the present research are 11.4 and 0.65 Hz, respectively. Also, the maximum and minimum values of amplitude of H/V peaks have been calculated as 3.71 and 1.19, respectively. The most significant point is that the fundamental frequency of the major part of Babol city is smaller than 1 Hz in agreement with the previous knowledge of the city geological setting. Another relevant point is the presence of some stations with very high (> 5 Hz) fundamental frequencies. In these cases, ambient noise recording and data analysis were repeated, but similar results were obtained. Considering the lack of sufficient geotechnical data (in some stations), the above phenomena need to be integrated with other methods. For this purpose, the data of electrical resistivity tomography (ERT) were used. The ERT showed that small regions of the north-west, west, and south areas have high resistance values probably related with the presence of hard deposits in the shallow subsoil. Babolrood river diversion in the west part and its return to the previous direction in the northern section is possibly due to the existence of these relatively hard deposits. By comparing these two tests, we observed that the ERT results correlate with the ambient data analysis. Therefore, we can conclude that the high-frequency peaks measured are reliable, but we need direct investigation to associate them to a specific shallow geological layer. To validate the results, fundamental frequencies obtained from ambient noise survey were compared with geotechnical data, numerical analysis and seismic data in the study area. A general review shows that the geotechnical data, equivalent-linear analysis results and seismic data have an acceptable conformity with the results of ambient noise survey.
Conclusion
The results show minimum and maximum fundamental frequencies 0.65 and 11.4 Hz, respectively. Assessment also reveals that the major parts of Babol city have the fundamental frequencies less than 1 Hz, which are in conformity with that of previous research. According to the results of seven cross sections, it can be concluded that fundamental frequency variations are in line with the geotechnical and geological data in the study area. It means that this method is the appropriate way to assess the local site effect in the Babol city. It is also observed that besides the soil layers, the soil stiffness and its shear wave velocity are effective factors in changing the fundamental frequency. Site frequencies were also estimated by preliminary 1-D site modeling using the equivalent-linear method. In general, a reasonable correspondence between the methods was obtained. Using seismic data, the HVSR of two strong ground motions have been calculated and the results have been compared with the nearest ambient noise recording station. Analyzing the spectral ratios demonstrates that the value of the fundamental frequency obtained by the H/V method (1.06 Hz) is very close to that of frequencies obtained by the seismic data (0.95 and 0.90 Hz)../files/site1/files/124/6rezaee%DA%86%DA%A9%DB%8C%D8%AF%D9%87.pdf

---

Introduction
The dispersivity phenomenon occurs due to the dissolution of some of the ions in clay soils or against the shear stress of normal water flow in cohesion-less soils. Water surface flows in low slopes cause surface erosion of dispersive soils. Dispersivity in the soil starts from a point and gradually expands; the starting point can be the holes from the activity of the animals, the existing cracks or the growth path of the roots of the plants. There is a lot of field evidence to recognize the dispersivity of the loess soils. In field investigations, soil dispersivity can be detected according to the following parameters: geological origin of the loess soil, mineralogical composition, gradation, drainage pattern, slaking of agglomerates, specific morphology, high permeability, geographical area (length and width relative to origin), soil color, relationship between slope and soil erosion, precipitation, erosion of column cracks, heeling, mud flowing runoff and the presence of salt crystals in loess soils. In terms of sedimentological characteristics and engineering geological properties, Golestan loesses have been dispersed in three areas 1, 2 and 3, which are consistent with the loesses of clay, silt, and sand types, respectively.
Material and methods
Loess soils in three regions of east and northeast of Golestan province were sampled. Sampling was conducted in two forms of wax-coated agglomerates and metallic cylindrical tubes. Depth of sampling follows the foundation of the buildings located on the Mehr Housing site and the Cheshme Lee village, varying from 0.5 to 2 meters. On the path of the Beqqeje Bala village, sampling was carried out from the path trench. After transferring to the laboratory, samples were subjected to gradation testing, Atterberg limits test to determine the unit weight of the volume and density.
The pinhole test was done on samples with the unit weight of normal volume (g_n) and maximum volume (g_dmax) and its rate of dispersion was determined. The research background, field evidence and the results of laboratory experiments indicate the dispersion of soil sampling areas. The results show that soil compaction reduces the severity of dispersion and decreases the flow rate, so that the flow rate has decreased in the Maravehtapeh sample by 38%, in the Cheshmeli sample by 13% and in the Beqqeje Bala sample by 43%. Compaction cannot eliminate the dispersion of soil. Adding nanoclay decreases the severity of soil dispersion and eliminates its dispersion properties in most cases.
In order to evaluate the effect of nanoclay on severity and to decrease the dispersion property of soil with ratios of 0.5, 1, 2, 3, 4 and 5 wt%, of Montmorillonite Nanoclay was added.
The nanoclay used in the present research was selected from the Sigma-Aldrich America Company called montmorillonite nanoclay and was purchased from its domestic representative, i.e. Iranian Nanomaterials Pioneers Company. The product has a density of 300 to 370 kilograms per cubic meter and a particle size of between 1 and 2 nm. The specific surface area of the nanoparticle is about 250 square meters per gram. Its color in normal light and in 1 to 2% moisture is yellow to yellowish buff.
Results and discussion
The rate of dispersion of samples with nanoclay was measured in Pinhole Test Apparatus. Also, the method of mixing nanoclay with dispersive soil shows different behaviors in severity of dispersion and its reduction. Given that the specific surface of nanoclay is high and this property can include the whole surface of soil grains as a sticky coating and increase soil cohesion, the mixing method is practically one of the most important steps in examining the effect of nanoclay on soil stabilization. At ratios of 0.5, 1, 2, 3, 4 and 5 wt% of nanoclay, nanoclay was mixed with soils of sampling regions by four methods:
In the method A, they were completely mixed with the preparation of a homogeneous mud from soil and nanoclay via an electric mixer.
In the method B, mixing of loess soil with nanoclay was performed in optimum water content.
In the method C, mixing of loess soil with nanoclay was conducted in the form of dough by hand mixer. In the method D, mixing of loess soil with nanoclay was carried out in the form of vibration dry by grading sieve shaker.
After mixing with nanoclay in the desired method (four methods A, B, C, D), the samples were first stored in sealed plastic containers for 24 hours. Then, the samples containing nanoclay were reconstructed in cylindrical mold of the pinhole device with the unit weight of maximum dry volume and moisture of two percent higher than the optimum moisture content and a hole was created in the middle of it. The samples remained in this position for 24 hours, and then the test was performed. Testing was carried out on each sample according to the standard D4647-93, and flow rate reading was done over a period of two minutes to 18 minutes.
Conclusion
The conclusion of this study shows that the three loess samples taken have a dispersivity potential and the flow rate is low in the unit weight of maximum volume, but the dispersivity potential does not eliminate. Adding nanoclay with any weight ratio reduces the flow rate and eliminates the soil dispersivity potential.
The results of this survey showed that 1% nanoclay weight ratio is technically and economically the most appropriate mixing ratio. With this weight ratio, the method of preparing homogeneous mud with an electric mixer (method A) produces the lowest flow rate, so that the flow rate from 1.3 ml per second in pure soil to 0.3 ml per second in the soil containing nanoclay is reduced by 50 mm. Therefore, it can be said that this method is more suitable, but it is not operationally efficient and the method B is more appropriate. In the method B, the flow rate reaches from 1.3 to 0.55 ml per second.

---

Introduction
Urban development and rapid extension of cities have been accompanied by a considerable growth in mechanized tunneling. The abrasivity of rock and even soil is a factor with considerable influence on the wear of tools. Soil abrasion and the resulting tool wear has a major impact on machine operation, utilization, and tunneling costs and time. One of the problematic aspects of working in abrasive grounds is the frequent need for the replacement of cutting tools, especially in pressurized face tunnel boring machines (TBMs). The effect of worn and damaged TBM cutter heads has been documented for numerous tunnel projects around the world. However, the lack of a standard or universally accepted test for soil abrasivity in geotechnical investigations has made the prediction of tool wear a difficult task.
Material and methods
A reliable prognosis of the abrasiveness of soils on a project would be of great benefit for designers, clients, and contractors. Many abrasion tests exist for rocks, and some have been proposed for soils; however, there is no universally accepted or international standard test for soil abrasivity testing. One of the most important and available tests in this field is LCPC abrasivity test which was developed by the Laboratoire Central des Ponts et Chaussées in the 1980’s. The LCPC Abrasivity Coefficient (ABR or LAC) can be used as a measure for both the abrasivity of the soil material and the influence of the grain size. The  abrasivity  testing  of  rock  is  controlled  by well-known parameters, whereas in soils many factors are influencing the abrasivity such as in-situ soil conditions, sedimentary petrology and technical   properties.
Tabriz metro line 2 Project about 22 km in length that will connect eastern part of the Tabriz city to its western part, considered as a case study. The project comprises a single tunnel which has been constructed using two earth pressure balance EPB-TBM with a cutting-wheel diameter of 9.49 m. In this study, based on geological and geotechnical properties, the tunnel route was divided into four parts and the abrasion and brittleness coefficients of alluviums determined by LCPC test. Besides that, the influences of some factors such as moisture content, mineralogy, grain size and shape, type and amount of foam have been studied.
Results and discussion
Based on more than 130 LCPC test results, in general, the Tabriz Metro’s line-2 route alluviums have the abrasion in the range of low to very high and the brittleness in the range of high to very high. In order to measure the effect of moisture content on abrasion and brittleness coefficient, the LCPC test was done on some samples related to the tunnel route in dried and moistened modes (5%, 0%, 15%, 20%, 25%, and 30%). Three types of sandstone, andesite, and conglomerate of the route were used to test the effect of moisture and petrology on abrasion. In a moisture range of 0 to 5%, in all types of materials, abrasion was increased. In a moisture range of 5 to 10%, abrasion was decreased in all three types, and this shows that a moisture level of 10% is a normal moisture content to create minimum abrasion. The behavior of sandstone and conglomerate is similar at higher moisture contents, and an increase in moisture content to 30% can increase abrasion of materials in both types. In conglomerate, abrasion at higher moisture levels is significantly more than in other modes. In andesite, an increase in moisture content to 20% can increase abrasion, although the abrasion is decreased with a moisture content of over 20%. In most samples, increase in moisture content led to decrease in brittleness of materials. In general, the highest abrasion level was related to conglomerate and the lowest level was related to sandstone. Moreover, andesite was at a lower level than conglomerate and a higher level than sandstone in terms of abrasion. Also, the results show that increased grain size led to increased abrasion, and the changes in andesite were greater than in sandstone.
In order to test the effectiveness of foam on abrasion, the foam used in workshops (A 168) made by Komeil Company Kashan was used for four types of petrography: conglomerate, andesite, sandstone, and silica. This test was conducted in the range of dried to 100 ml foam. In all types, decreased abrasion is observed from 0 to 20 ml and increased abrasion is observed from 20 to 100 ml.
Conclusion
The following conclusions are drawn from this research.
- With regard to the effect of grain size, increased size of grains could lead to more abrasion and less brittleness
- In terms of the effect of mineralogy, the conglomerate had the most effect on abrasion. In terms of brittleness, andesite was the most brittle.
- When the foam is moisturized in the sample, minimum abrasion is observed and above this level, the abrasion is increased.
./files/site1/files/134/4.pdf

---

Introduction
The landslides, as a natural hazard, caused to numerous damages in residential area and financial loss. In many cases, we can forecast the occurrence probability of this natural phenomenon with using of detail geological and Geomorphological studies. This seems that one of the most effective parameters in landsliding phenomenon is structural parameters, especially faulting in rocky outcrops. For verifying this hypothesis, the Nargeschal area, as high potential of hazardous area, is selected as case study for investigation on influences of faulting on landslide occurrence probability. Many large composite landslides were happened in 2016 and hence, this area is enumerated an active zone of landsliding. This area with geographic attitude 55° 09' 06" to 55° 27' 21" Eastern Longitude and 36° 54' 23" to 37° 05' 15" Northern Latitude located in south of Azad shahr (in Golestan Provinces) placed in Northeastern of Iran.
Geological studies indicate that this area located in northern limb of Alborz fold belt (as a young fold-thrust belt with 900 km length) which formed in late Alpine orogenic events by convergence Afro-Arabian and Eurasian plates. In this zone, the structures have main NE-SW trends with main active faults such as Khazar and North Alborz faults, as reverse faults with north-ward movements. The remnant part of Paleotethyan rocks (which transported from collision zone toward southern part by low angle thrusts) located between these faults and formed the mountain-plain boundary hills.
Material and Methods
In this research, we investigated on effective parameters in landslide occurrence probability of Nargeschal area with using of remote sensing techniques, GIS environment abilities and complementary field investigations. Therefore, we have prepared the seven data layers of geological and morphological effective parameters which are affected on landslide probabilities. These data layers consist of: lithology of outcropped rocks, faulting condition, topographic slopes categorizes cultivation circumstances, seismicity condition, spring population (ground water condition) and surveyed occurred landslides. Then, the content of each data layer is weighted and classified into five classes in GIS environment. Finally, the content of each pixels in all of 7 layers are algebraically summed and recorded as an attributed table. Hence, the landslide hazard zonation map was prepared by drawing the isopotential surface map on the basis of quantities of attributed table by using of GIS functions in Arc view 3.2 software.
Results and Discussion
The results of this research illustrate that a high risk zone is located in central part of area as an oblique broad-stripe zone with NE-SW trend [6]. This zone is correlatable with high density of fractures zone and high population of springs and earthquake focus and also, taken place in Shemshak formation with shale, marl and siltstone rocky outcrops (upper Triassic- Jurassic in age). 
Also, the results of investigations on influences of structural parameters (especially faulting) in landslide hazard demonstrated that faults are indirectly impressed on this hazard probabilities via formed the high slope topography, poor strength faulted rocks, locating of spring presences and creation of seismicity, and hence, defined the spatial pattern of landslides.
Conclusion
Nargeschal area in Northern limb of Eastern Alborz is selected as case study for investigation on temporal relationship between Faulting and Landslides. The following conclusions were drawn from this research.
- It seems that the fault surface plays the role of rupture planes for landsliding.
- The structural factors also increased the ground slope and then, the close relationship is formed between landslides and faults.
- The results demonstrate the genetically relationships between landslides and faults in macroscopic scale in Nargeschal area.