Journal of Engineering Geology

---

The world financial crisis has drastically raised the costs of hydrocarbon materials. This simply manifests the strategic significance of crude oil storage. Regarding the special rank of the oil in Iran’s economy, storage industry development can be one of the solutions to control such a crisis. Underground storage of crude oil in synthetic structures (rock caverns, salt caverns, and obsolete mines) and natural structures (depleted fields of oil and gas, underground water resources, and natural caves) is possible. Among these possibilities more adaptable to the environment is the most appropriate. Due to the existence of many caves in Iran, crude oils storage in natural caves is a proper option. It is clear that if natural caves are used instead of caverns, much can be saved. The present article intends to choose a proper cave for crude oil storage through studying the natural caves based on a combination of fuzzy analytical hierarchy process (FAHP) and technique for order performance by similarity to idea solution (TOPSIS). The likely option is chosen. Roudafshan Cave is considered appropriate for crude oil underground storage based on several qualitative and quantitative criteria including tourism and environment protection regulations, capacity, distance from both main pipes of crude oil transfer and country's major petroleum factories. It should be noted that these criteria are ranked by an experienced team. This cave is located in the north east of Tehran in Firoozkooh and has three passageways which are among the largest ones in the country. Generally, its capacity is estimated to be about 250,000 square meters

---

The Bakhtiari dam has located on Bakhtiari River in province of Lorestan. In order to access the crest of the dam, the excavation of a spiral tunnel is being studied. There are other access tunnels which are branched from this tunnel in different levels and are connected to grout galleries. According to the fact that this tunnel will also be used during the operation of the dam,The correct determination of mechanical parameters of rock masses for tunnel design and stability Analysis is very important. In order to analyse the stability of the underground rock structures, the mechanical and engineering parameters of the rock mass must be known. Accurate rock mass properties can only be obtained from large in situ tests. Such tests are seldom carried out as they are very expensive and time consuming. Sensitivity analysis of parameters can be applied for the optimisation of testing schemes. Sensitivity analysis helps to avoid mistakes due to subjective conjecture. In this article, after the introduction of regional geology and determination critical section on the tunnel path, the mechanical parameters of the rock mass surrounding the tunnel are modelled and analyzed by using FLAC3D software (numerical finite difference method). Parameters conducted in the analysis include the elasticity modulus (E), cohesion of the rock mass (C), friction angle (ϕ), coefficient of lateral stress (K) and tensile strength (&sigmat). Ultimately, according to the result of numerical modelling and parametric analysis, parameters affecting the stability are prioritized. The result of analysis showed that in this project, tensile strength of the rock mass does not affect the stability of the tunnel, and Also, in order of priority, E, ϕ, C, k parameters are important in design. The amount of field tests for rock parameters can be rationalised according to their sensitivity factors.

---

./files/site1/files/4Extended_Abstract.pdfExtended Abstract
(Paper pages 73-90)
Introduction
Up to now, various indexes and methods have been presented for evaluating the abrasivity of rocks. In total, these methods can be divided to two main groups; the methods based on nature of rocks, methods based on heuristic tools. Schimazek F-abrasivity index is one of the most powerful and applicable indexes for evaluating the rock abrasiveness. This index uses the grain size, Brazilian tensile strength and equivalent quartz content for abrasivity analysis. Since the values of these parameters are equal in Schimazek index, therefore, in some cases this index doesn't have suitable ability to distinguish and classify the rock abrasiveness. This paper tries to modify the Schimazek index considering the weights of its applied parameters.
Material and Methods
In this research, Fuzzy Delphi Analytical Hierarchy Process (FDAHP) has been used to calculate the weight of dominant parameters in rock abrasivity. For this purpose several questioners have been distributed and the expert opinions were collected. The results showed that the quartz content, grain size and tensile strength have the weight of 0.4, 0.31 and 0.29 respectively and new Schimazek F-abrasivity index is as presented in equation (1).
    
In the next stage, in order to facilitate the application of new index, a new classification system was developed. This classification and related weighing graphs (Figure 1) help to change the discontinuous classification to continuous one.
Results and discussions
In order to verify the application of the new developed index, ten ornamental stones have been studied and the old and modified Schimazek indexes were calculated for all of them. Then, the cutting rate (sawing rate) of each stone was recorded in laboratory and the mathematical relationships between new and old indexes have been achieved. The results show that the new Schimazek abrasivity index has higher ability to predict the cutting rate than old one (Figure 2). 

 
Figure1. Continuous weighting for parameters of Schimazek F-abrasivity index


Figure2. Regression of old and new Schimazek F-abrasivity index with cutting rate of granite ornamental stones
Conclusion
Generally it could be concluded that, the main weakness of Schimazek F-abrasivity index which is the equality of parameters’ importance, has been removed by idea developed and confirmed in this study. The different weights which allocated to grain size, Brazilian tensile strength and equivalent quartz content in study, improves the Schimazek index applicability in rock engineering applications specially rock cutting and drilling. Therefore, it is recommended to use new method instead of old one in future applications.
 




 

---

./files/site1/files/7Extended_Abstract.pdfExtended Abstract
 (Paper pages 135-156)
Introduction
Many civil structures (e.g. tunnel walls, bridge pillars, dam abutments and road foundations) are subjected to both static and dynamic loads. Cyclic loading leads to occurring fatigue phenomenon. Fatigue is the tendency of materials to break, or the process of damage accumulation, under cyclic loading. It was found that the dynamic fatigue strength can be reduced by 30-70 percent on average compared to uniaxial compression strength. Different materials show different response when they are subjected to cyclic loading. Some materials become stronger and more ductile, while others become weaker and more brittle. Although it is clear that the mechanical properties of rock under dynamic loads varied dramatically from those under static loads, the nature of dynamic failure in rock remains unclear, especially in cyclic loading condition. Fatigue behavior of rocks was rarely studied in respect to other materials such as steel and soil. The performed researches on fatigue behavior of rocks indicated that fatigue life will be decreased by increasing load amplitude in logarithmic and exponentially pattern. Also, strain softening is the dominated behavior of rocks against cyclic loading. Furthermore, some parameters such as maximum load level, confining pressures, amplitude, and loading frequency have considerable effects on fatigue behavior of rocks. However, available data on fatigue behavior remain insufficient for solving the practical tasks of predicting rock bursts and earthquakes. Obtained results are inconclusive and sometimes discordant. The aim of the current work was to assess tonalite rock fatigue behaviour under different loading conditions to describe the fatigue damage process of the granitic rock.
Material and methods
Several core samples were prepared to perform this research. The core samples were prepared with a L/D ratio of 2.5 with an average diameter of 54 mm. Before the fatigue tests, the physical and mechanical properties of the rocks were measured. Uniaxial compressive strength test (UCS) has been done on 5 core samples. The tests were performed in the load-control mode with a 1.6 kN/s loading rate. The tests were conducted to obtain the physico-mechanical parameters of the rocks in static loading condition, and provided a reference for subsequent dynamic tests. The cyclic tests were performed in both load and displacement control modes. To record axial and lateral strains during the fatigue tests, four strain gauges have been employed with arrangement of two axial and two laterals. Also, three acoustic emission sensors were installed on top, mean and bottom of the core samples to record cracking sound. In order to doing the tests a servocontrol Instron machine with 500 kN capacity was employed. The fatigue tests were conducted with three different maximum loads, 1 Hz frequency, and constant amplitude (0.82 of uniaxial compressive strength). The maximum stress level (the ratio of maximum cyclic stress to static strength) was varied 0.80, 0.85, and 0.90. The amplitude level (the ratio of amplitude stress to static strength) ranged from 0.50 to 0.70 and 0.90. Finally, Multi stages loading with increasing amplitude were applied for the displacement control tests. The results of fatigue tests have been evaluated by fatigue damage parameters including maximum and minimum axial strain, maximum and minimum lateral strain, tangent and secant modulus, toughness and hysteresis energy.
Results and discussion
The obtained results indicated that during fatigue process failure occurs below the maximum strength loading condition as a result of accumulative damage. Analysis of the fatigue test results showed that the fatigue failure consisted of three stages: fatigue crack formation (initiation phase I), stable crack propagation (uniform velocity phase II), and unstable crack propagation resulting in a sudden breakdown (accelerated phase III). By comparing the axial and lateral deformation, it was found that lateral deformation is more sensitive to fatigue. At higher stress levels, considerable part of fatigue life is response to crake development, whereas at lower stress levels, crack acceleration phase of fatigue life is distinguishable. Descending trend of loading and unloading tangent modulus shows a scatter pattern. This behavior may be related to the calculation method and loading condition, as well as microstructure and behavior of the rock mass. In spite of tangent modulus results, the three-stages of damage process (especially phase I and II) for secant modulus in both loading and unloading conditions are clear. The result is due to the method of calculation and increase in axial strain with increasing number of cycles. Brittle behavior of this type of rock leads acceleration phase to be hidden and unclear in most of fatigue damage parameters. A dramatic decrease of toughness and hysteresis energy in the first few cycles is due to the closing of pre-existing micro fractures. In fact, during the initial cycle, the rock behaves in a more ductile fashion than in the next few cycles. Thereafter, toughness begins to increase slowly, then steadily, and finally rapidly. A similar behavior was found for hysteresis energy as well. This fact indicated that cracks generated in parallel to loading direction. Fatigue displacement control tests show a strain softening behavior for the granitic rocks. This behavior is highlighted in variation of maximum stress during the tests. This parameter, especially in final step of loading, shows distinguishable decreasing trend.
Conclusion
The tonalite rocks were subjected to uniaxial cyclic loading in both load and displacement control mode. The following conclusions were drawn from this research.
-Accumulated fatigue damage occurs in an obvious three-stage process. This is the result of the micro-fracturing mechanism in the fatigue process.
-By comparing axial and lateral strain damages, it was found that crack propagation occurred in the loading direction and crack opening occurred in the lateral direction. So, among fatigue damage parameters, lateral strain shows the best three-stage fatigue damage behavior.
- Strain softening was found as rock response to cyclic displacement control loading.

---

Introduction
Exploitation or processing of ores is usually associated with the production of a large amount of waste materials. These materials often have a high concentration of metals which can enter the environment through weathering or erosion. It is well-known that the measurement of the total concentration of metals cannot be an adequate for evaluating the pollution status of soil. Therefore, in most studies on soil contamination, bioavailability content of metals is determined by which can predicate the fate of the metals entering into the other parts of the environment such as plants, water or human food chain. The bioavailability of metals in the soil environment is the exchangeable and absorbable metals for plants, which depends on their exchangeability and absorption by soil organisms especially plants. This is also the function of the chemical form of each element in the soil.  The main purpose of the present study was to measure the total concentrations along with the bioavailable content of metals in soils and plants around the Irankuh mine tailing dams.
Area of study
The Irankuh lead and zinc mine is located 20 kilometers southwest of Isfahan. This mine is of MVT type Pb-Zn deposit which occurred mainly in limestone and dolostone of lower cretaceous age. The Irankuh mine is an open-pit mine with annual extraction of 358 thousand of PbO and ZnO. The exploitation of mine is also associated with the production of a large amount of waste material which is piled in open dumps around the mine. The main minerals of ores are galena, sphalerite and pyrite.
Materials and methods
31 sampling sites were selected randomly for collecting agricultural soils around the tailing dams. Each soil sample is actually composite sample of four samples which are taken from a depth of 15 to 20 cm. Seven cultivated plants (Ocimum basilicum) were sampled from green houses in the vicinity of tailing dams. After drying and sieving, about 50g of the soils are chemically analyzed in order to determine the total concentration of the metals by the ICP-OES method.  Plant samples after drying were changed to ash in the furnace at temperature > 500 C. The concentrations of metals (Zn, Pb and Cd) were then measured by Atomic Absorption Spectrometers in their stem, roots and leaves.
pH samples of soil were also determined using the EPA 9045 method. Walkley and Black method were used to measure the amount of organic matter. The cation exchange capacity (CEC) of soil samples was also determined based on EPA 9087 method. Soil texture determined using hydrometric method and then classified according to USDA classification. Diethylene Triamine Pentaacetic Acid (DTPA) extractable metals (bioavailable content) were determined using the method by Lindsay and Norvell (1978) and their concentrations in the DTPA extracts were determined by Atomic Absorption Spectrophotometer (AAS).
The metal transfer from soil to plant was calculated using the transfer factor (TF: metal content in plant divided by metal content in soil).
Results and discussion
The soil pH of the studied samples varies from 7.36 to 8.35. Cation exchange capacity (CEC) of soil samples was estimated to be in the range of 4 to 22.2 Meq/100 g. Also, the amount of organic matter in the studied soil samples varies from 0.17 to 3.43%. The relative high levels of soil organic matter are probably due to addition of organic manure to soil through agricultural activity. The total concentration of these three matls are significantly higher than their corresponding values in the crust implying that the mining activity and tailing dams greatly elevated the concentration of these metals in soils. Statistically, there is a significant positive correlation among Zn, Pb and Cd (at confidence level of 0.01) indicating that their potential source is the same or having similar geochemical behavior in the soil. The soil clay content showed a significant correlation at the level of 0.05 with Zn, Cd and Pb. This indicates that clay fraction plays a significant role in absorption of these metals in soil. According to the results of single extraction (DTPA method), the proportion of available content for Cd is higher than that of Zn and Pb. Cadmium is often characterized by its high mobility in soil media. Based on the correlation coefficients at the confidence level of 0.01, it is also observed that the increase in total concentration of Cd increased its bioavailability content in the soil consequently increase the availability of other elements in the soil. Therefore, it can be inferred that the availability of Cd in the soils of the study area is likely to be increased in the presence of Zn and Pb because in sites where the total concentration of Pb and Zn is high, the content of Cd availability has also elevated.
Based on the comparison of the average concentration of the metals in different parts of the plants, the concentration of metals is ordered as follows stem> leaf> root, which indicates the high root capacity for the accumulation of metals. The average transfer factor (TF) for Cd is obtained much higher than those of Zn and Pb. There is also a negative significantly correlation between the concentrations of Cd in the aerial parts of the plants and its bioavailability concentration in the soil. Also, there is positive and significant correlation between Zn and Cd for all three different parts and its bioavailability concentration in the soil. In the case of Pb, a significant correlation is observed between stem and root parts. This means that Cd and Zn after being absorbed by the root, are more likely being uptake by the plants due to high mobility of zinc. However due to less mobility of Pb, it is seemingly entered into the plant aerial parts after absorption by the root.
 
Conclusion
The concentration and degree of contamination of the studied soils is very high in terms of total Pb, Zn and Cd concentrations in agricultural soils around the Irankuh mine. The increased heavy metal contents in soils can be attributed to mining activity and tailing dams near cultivated lands. The measurement of the bioavailable content of these metals indicates that the Cd has the highest availability as compared to Zn and Pb. The average concentration of Pb and Cd in different parts of plant which is higher than the permissible limits, implying that the transfer of the available metal part (especially Cd) from the contaminated soil into the plant. Based on the calculated health risk assessment index in this study, it can generally be concluded that the gradual accumulation of these metals, especially in aerial parts of basil might have health hazards for local consumers.   ./files/site1/files/0Extended_Abstract3.pdf

---

Introduction
It is very important to have knowledge on the rock deformation modulus when designing geotechnical ‎structures and modeling oil reservoirs. In general, there are two destructive or static and non-‎destructive or dynamic methods for determining the rock deformation modulus, but considering the ‎time and cost of destructive methods proportionate to the depth, it is more common to make use of ‎non-destructive approaches. The outcrops of Asmari Formation are widely spread in the west and ‎southwest of Iran, and many engineering projects have been constructed or are being studied ‎on this formation. Therefore, it is of great importance to study on the geomechanical characteristics of this ‎formation. Presentation of empirical relations regarding the relationship between static and dynamic ‎moduli, with respect to the studies carried out in other parts of the world and the dispersion and ‎independence of studies done on Asmari Formation due to its large extent on one hand and the ‎importance of this formation in terms of oil and development civil projects on the other hand, necessitate ‎presenting a comprehensive criterion resulted from all studies carried out on Asmari Formation which ‎can express the relationship between the static and dynamic moduli. This paper represents the ‎relationship between the dynamic and static moduli of the site using the moduli obtained by the ‎down-hole geophysical method and the static moduli obtained by the intact rock test results of ‎Ghalajeh tunnel located in Asmari Formation in Ilam province. Then, a comprehensive relation is ‎presented to express the relationship between static and dynamic modulus by studying the previous ‎researches and criteria on this formation.
Material and methods
Two sets of tests were conducted to determine the relationship between static and dynamic moduli in the Ghalajeh tunnel. First, a uniaxial compression strength test was performed on 13 cores taken from three boreholes to compute the elasticity modulus in accordance with ISRM standard. Then, down-hole test was conducted on two boreholes such that to determine the dynamic modulus using compressive and shear wave velocities. Seismographic apparatus of ABEM RAS 24 as well as three-component down-hole geophones were utilized in order to plot the seismic profile. After the performing the tests, the dynamic modulus of deformation was calculated using the velocity of P-waves and the density of the host rock.
Discussion and Conclusions
By conducting in-situ static and dynamic laboratory tests on Ghalajeh Tunnel project and determining the values ​​of the static and dynamic deformation moduli, a relation was presented between them. Then, taking into consideration the previous models studied in Asmari Formation, a comprehensive criterion was presented for wider use in the mentioned formation. Given the root mean square error (RMSE) and variance account for (VAF), the values predicted using the proposed comprehensive model have acceptable accuracy. In the interim, the correction factor between dynamic and static moduli in Asmari Formation was between 0.8 and 2.4. The results show that, in general, the relationship between static and dynamic moduli is linear up to a certain range (static modulus of 100 MPa) and then it has a power trend./files/site1/files/124/4darai%DA%86%DA%A9%DB%8C%D8%AF%D9%87.pdf

---

Introduction
     Ground-penetrating radar (GPR) method is a pretty new, non-destructive and high-resolution geophysical method that is widely used to identify the thickness of snow and ice layers and glaciers bed, because snow and ice are transparent for electromagnetic (EM) waves. Therefore, this method has been used to determine the thickness and basement topography of Alam-kooh glacier. In this research, only the GPR acquired data using unshielded antenna with central frequency of 25 MHz along one line in Alam-kuh glacier, Kelardasht- Mazandaran, have been processed and interpreted. The GPR data acquisition has been done by using common offset method, and transmitter-receiver separation of 6 meters. The final real radargram related to one of the surveyed GPR profiles in this region has been prepared after applying various processing operations containing signal saturation correction, amplitude gain, f-k migration filtering and static (topography) correction on the raw data. After applying processing sequences on the acquired data, the EM waves reflection off the interfaces of different layers including the reflections from the glacier basement have been detected, and by assigning a suitable EM wave velocity in the ice (0.16 m/ns), the thickness of 50 m for the ice layer laid under the survey line has been estimated. Also, in present research, forward and inverse modeling of GPR data have been performed to employ for snow, ice and glaciological investigations in the AlamKooh region of Mazandaran. To achieve this goal, GPR response of synthetic model corresponding to the real radargram was simulated first, by 2-D finite-difference time domain (FDTD) method. Afterward the inversion method by solving an optimization problem was employed to validate the interpretation of real GPR data.
Methodology and Approaches
     Based on the nature, physical and geometric properties of the subsurface target in the field data, their synthetic model have been built and their two-dimensional GPR responses forward modeling using ReflexW software and finite difference algorithms improved in the frequency domain, have been obtained. Also, it has been used an effective algorithm, coded in GUI environment of MATLAB programming software and as a result, a reliable and accurate inverse modeling has been carried out. In the present study, to simulate the behavior of the propagation of EM waves in GPR method, two-dimensional finite difference method has been used. The main advantage of this method is its comparative simplicity of the concept, high accuracy and simple implementation for complex and arbitrary models as well as easily adjusting the antenna when applied. In this study, acquisition of GPR field data and synthetic data modeling have been carried out in TM mode. The radargrams of the GPR data have been demonstrated using ReflexW software after performing necessary processing sequences.
Results and Conclusions
     The obtained results reveal that moraine materials covering the surface of the area are mainly fine-grained granite. The bed-rock or basement in the area is also granite. The polarity representing ice-bed rock is clearly seen on the GPR profiles. The topography of the glacier basement has successfully been detectable using just by GPR method. The electrical resistive nature of the glacier has caused large penetration depth of GPR pulses in this research. Furthermore, the results of the research for presented profiles on the basis of forward and inverse modeling output of GPR data in comparison with real GPR radargrams in the region validated the accuracy of GPR investigations in the area. Although with a quick glance, the error obtained by the inverse modeling for real GPR data seems unexpected and unacceptable, absolutely the high rate of error depends on many factors influencing on the real earth models containing various limitations existing in all forward modeling algorithms and software packages, impossibility of making forward modeling exactly according to the real models (due to the complex nature of the ground), taking into account the homogeneity and uniform host environment and targets in the modeling process unlike the diversity, the presence of different types of noises and so on. Therefore, making a controlled geophysical test site and trying performance of inverse modeling algorithm for field GPR data in this site, as well as determining the important physical parameters such as dielectric permittivity and electrical conductivity by experimental method through sampling from different depths for complex geological environments are suggested../files/site1/files/124/1ahmadpur%DA%86%DA%A9%DB%8C%D8%AF%D9%87.pdf

---

Introduction
"Sulfide-carbonate" deposit is a term, which comprises a series of sulfide minerals such as Zn-Pb ore minerals, mainly considered as related to weathering of Zn-Pb sulfide concentrations and influence in sedimentary hosts (carbonate). There are more than 350 Zn-Pb deposits located in Iran, including world-class deposits such as Angouran, Mehdiabad and Irankouh. Due to the mining activity of these deposits, it creates a significant amount of mine waste that releases of these wastes in the environment causing severe problems. One of the main problems is the formation of Acid Mine Drainage (AMD). AMD is produced by oxidation of sulphide minerals, particularly pyrite (FeS2) in waste dump. Due to low pH and the ability to dissolve metals and other compounds, it can host a number of environmental problems. A phenomenon known as natural or alkaline mine drainage (NAMD) occurs at high pH values ​​when the neutralizing minerals are significantly present in the mine waste or when the oxidation of the sulfide minerals is poor. However, the metals and cationic species, such as Cu, Pb and Cd, are more soluble at low pH. In contrast, elements that form anionic species, such as Se, Cr, V, and Mo, tend to be more soluble at high pH and Ni, Zn, Co, As, and Sb, are soluble at near-neutral pH, and can potentially contaminate mine effluents, even without acidic conditions. Therefore Acid or Neutralization potential (AP&NP) of waste dump is significantly affects on the composition, transfers and fates of contaminations transmitted from waste dump. The aim of this study was to monitoring heavy metals concentrations and assessments of pollution potential of waste dumps in Anguran mine by static method and has been compared by mineralogical approach.
Material and methods
The Angouran Zn-Pb deposit is located in the 135 kilometers southwest part of Zanjan Province, NW Iran. This area belongs to the northwestern part of the Sanandaj-Sirjan Zone, a metamorphic belt related to the Zagros orogeny. Angouran mine is one of the most important carbonate hosted Zn-Pb deposits in Iran that mining activity has been created a significant amount of waste dump in around pit. To achieve the goals, the 47 samples taken from different surficial parts of the waste dump were analyzed by using the ICP-MS method to determine the concentration of elements and heavy metals. These elements and metals includes: Ca, Mg, S and As, Cd, Cr, Cu, Ni, Pb, Zn. The pollution index (PI) were modeled for heavy metal contamination risk zoning then modified Acid Base Accounting (ABA) static method was used to evaluate of acid and neutralization potential (AP&NP) of the waste dump samples and the results were modeled by Kriging method. At the end, mineralogical approach (Mg + Ca concentration) was used to determine the source of neutralization and to better interpret the static results.
Results and discussion
The results of contamination index showed that zinc, arsenic and cadmium had the highest average contamination index (18.89, 12.13 and 5.8, respectively) and the trend of total metal changes in the region as Zn> As> Cd> Pb > Ni> Cr> Cu was rated.
Datas measured in modified ABA method were modeled in 2D maps using the Kiriging method. Due to the low total sulfur content (less than 1%), all of the samples were Net Neutralization Potential (NNP) with a range of 49- 990 kg calcium carbonate per ton, and the study area was classified into three neutralization potential (NP), High (NP) and Very High (NP) levels. The mineralogical approach (Mg + Ca concentration) was used as a useful tool for better interpretation of modified ABA results and determines the neutralizing source. Mineralogical approach results indicate that calcite species are the main source of neutralization and have high correlation coefficient (R = 0.99) with the modified ABA method. In order to validate the results, the presence of mineral calcite was confirmed by XRD analysis on 4 samples.
Assessment of AP and NP of sulfide – carbonate waste dump in this research can be used as a basis model for other similar mines to control environmental problems and to identify the behavior and to transfer heavy metals in mine drainage in the future. Mineralogical approach results show that neutralizing potential and neutralizing source can be obtained without using expensive mineralogy analyses in this type of carbonate-sulfide deposit



 

---

Introduction
Shallow tunnels have a vital role in urban planning, railway and highway transportation lines. The presence of underground cavities can leads to stress concentration and consequently, instability of the spaces against static and especially dynamic loads. Therefore, the aim of this study was to evaluate the effect of elliptical cavity and its inclination on sandstone rock behavior under compressive static and tensile dynamic loads. In order to evaluate the effect of the cavity under static stress conditions, two groups of intact and hole-bearing sandstone cores with 0, 30, 60, and 90 degrees of hole inclination were prepared and tested under uniaxial compressive loading test. During the test, in addition to the stress recording, damage and deformability of the samples were recorded by using the strain gauge, acoustic emission sensor and camera. Split Hopkinson pressure bar (SHPB) test apparatus was used for doing dynamic loading test. Furthermore, the damage process was recorded using a high-speed camera with 10 micro-seconds interval of frame capability. The obtained results showed that presence of the cavity reduced the rock strength in maximum state (θ=0) up to 55% and in minimum state (θ=90) up to 77% of its initial uniaxial compressive strength. Dynamic tensile loading tests illustrate that the elliptical hole near the free end of sample (reflection boundary of compressive wave to tensile wave) is stable due to locating in superposition area, while the other cavity out of the area with each inclination was undergone to spalling failure. Assessment of failure surface using scanning electron microscope and thin section study indicates that the dominant fracture is grain-boundary type and iron oxide cement has a vital role in developing of this type of fracture.
 


 

---

Chahar-Gonbad region of Kerman province is geologically located in the southern part of central Iran zone, dominantly in Uromieh-Dokhtar volcanic belt. In this region, many high potential prospects, specially Cu-Au mineralization, have been detected during large scale exploration and reconnaissance phases. In this paper, remote sensing and field geophysics were used for alteration mapping on the surface and ore body delineation on the subsurface, respectively. To this end, we used an ASTER satellite image and different maps were generated by spectral technics such as false color composites and spectral ratios. Results showed argillic (and phillic) alteration in Bab-Zangoeie area is surrounded by propylitic alteration, which could be a promising evidence for Cu mineralization. Integrating these results with previous exploration studies led to selecting target area selection for ground study and field geophysics. We used both induced polarization (IP) and resistivity (RS) methods as two powerful geoelectrical methods by a pole-dipole array along four profiles. After preprocessing analysis, forward and inverse models were constructed in 2D section and 3D overlay model of joint IP/RS anomalies were constructed. Based on the obtained results, the deposit in depth where we proposed drilling targets. Further drilling operation have proved the mineralization in our proposed targets../files/site1/files/152/%D9%86%D8%B8%D8%B1%DB%8C.pdf
 

---

Acid mine drainage (AMD) as the most important environmental issue in mining sites is considered a significant source of environmental pollution.  AMD is typically produced by the oxidation of sulphide minerals, especially pyrite. The present study aims to investigate the acid production potential of the wastes of Mehmandoost coal washing plant located in NE Damghan. For this purpose, mineralogical, geochemical, and statistic tests were carried out on 7 representative coal washing waste samples. The obtained results show that although coal washing wastes are not enriched in Cu and Mn, they are moderately enriched in Ni and Co, significantly enriched in Cr, Sb and Zn, strongly enriched in Cd and As, and extremely enriched in Pb and Mo. The main mineral phases presented in the studied samples include quartz, muscovite, clinochlore, kaolinite, illite, montmorillonite, calcite and pyrite. In most of the studied samples, the pH and electrical conductivity (EC) of the saturated paste is <3 and > 2000 μm/cm, respectively. Moreover, in most samples the Net Neutralization Potential (NNP) is < -20. Also, in most of the samples, the Net Acid Production Potential (NAPP) is positive and the Neutralization Potential ratio (NPR) is < 3. The pH of Net Acid Formation (NAG pH) of these samples is < 4.5 and the ratio of Acid Neutralization Capacity to Maximum Acid Potential Acidity (ANC/MPA) is < 1. According to the results of static tests, there is a possibility of production of acidic drainage by the studied samples, therefore, taking suitable management measures to control acid production in the area is of crucial importance.

 

---

---

---

---

---

---

---