Journal of Engineering Geology

---

Introduction
The geotechnical engineering problems involving unsaturated soils are included water flow, shear strength and volume change. Soil-water characteristic curve (SWCC) describes the constitutive relationship between soil suction and soil water content. SWCC may be determined directly or indirectly in the laboratory. Because of the various difficulties involved in the direct measurements, a simple and economical laboratory method namely filter paper method is of considerable value. The filter paper method is a laboratory technique that has recently been accepted as a standard method of measuring soil potential, reaching far higher ranges of water potential in comparison to other techniques, and is based on the principle of moisture absorption by filter paper until there is a balance in potential between filter paper and soil.
This paper presents an experimental investigation performed to evaluate the soil water characteristic curves of dune sand stabilized with SBR polymer and MICP processes (Sporosarcina pasteurii bacteria with CaCl2 and urea) with contact filter paper method in the Jabal Kandi area.
Material and methods
The dune sand used in this study was obtained from the surface (0–10 cm depth) of Jabal kandi area, located on the south-west of Urmia Lake. SBR polymer is prepared from Paya Resin Company in Esfahan. In the MICP processes, S. pasteurii from Persian Type Culture Collection (PTCC 1645) was used as the urease positive bacterium. Cultivation of the microorganism was conducted in a medium containing 20 g l^-1 yeast extract, 10 g l^-1 NH₄Cl at a pH value of 8. Sporsarcina pasteurii was grown to late exponential phase to final concentration of 1.5 g dry weight l^-1 and urease activity of 2.2 mM urea min^-1 under aerobic batch conditions. Broth cultures were incubated in a shaker incubator operated at 120 rpm. Cementation solution of MICP consisted of CaCl2 and urea. All experiments were performed at an ambient temperature of 25^oC ± 2.
For the tests with Whatman No. 42 filter paper, three different soil samples were prepared (dune sand, dune sand stabilized with (5-10-15) % SBR polymer and dune sand stabilized with (5-10-15) % MICP process). Residual water content is 2.5% and the residual dry density is 15 kN/m³. The soil is mixed with the right quantity of water and placed in a sealed plastic bag for 24 hours to allow the hydric equilibrium to establish. The contact filter paper tests were carried out on soil specimens stabilized with SBR polymer and MICP process to the residual water content (2.5%) and nearly residual dry density (15 kN/m³). The soil specimen sizes were 50 mm in diameter and 20 mm height. The test procedure involves placing a piece of initially air dry filter paper against the soil specimen whose matric suction is required and sealing the whole to prevent evaporation. The filter paper was wetted to water content in equilibrium with the magnitude of the soil matric suction, and careful measurement of the water content of the filter paper enables the soil matric suction to be obtained from a previously established correlation. This provides a measure of the matric suction. ASTM D-5298-93 standard is used for the filter paper method.
Results and discussion
The SWCCs for dune sand stabilized with SBR polymer and MICP process under different SBR polymer and MICP process contents are illustrated in this study. Gradual transition from a unimodel SWCC to a bimodal SWCC was observed as SBR polymer and MICP process content increases. The unimodel SWCC is characterized by having two bends defining the air entry value and residual water content. The air entry value is defined as the matric suction above which air commence to enter the soil pores. The residual water content is defined as the water content beyond which no significant decrease in water content occurs. The bimodal SWCC is characterized by having four distinct bindings: two air entry values and two residual water contents. For SBR polymer and MICP process content equal to or less than 5 percent, the SWCC shows a unimodal form of SWCC. With the increase of SBR polymer and MICP process content greater than 5%, the SWCC indicate a bimodal form. It is further observed that the residual water content and the air entry value increases with the increase of SBR polymer and MICP process content. These observations are attributed to the presence of smaller pore size developed as a result of SBR polymer and MICP process particles filling the voids between sand particles. Bimodal SWCC are generally observed for gap-graded soils as well as soils that include two levels of pore sizes defined as macro pores and micro pores. Therefore, it can be inferred that the increase of SBR polymer and MICP process content, resulted in the formation of micro pores within the dune sand stabilized with SBR polymer and MICP process. The portion of the soil water characteristic curves representing macro pore sizes range between matric suction of 0.1 to 100 kPa. Whereas, the portion of the SWCC representing micro pore sizes lies between matric suction of 200 and 1500 kPa.
Summary and Conclusions
In this study, the effect of SBR polymer and MICP process content on the soil water characteristic curves of dune sand was evaluated. SBR polymer and MICP process contents considered include 0%, 5%, 10% and 15%. Results from this study indicated that, as the SBR polymer and MICP process content increased, the shape of the SWCC transforms from a unimodal form to a bimodal form. Furthermore, the air entry value and residual water content were observed to increase with increase in SBR polymer and MICP process content signifying increase in water retention capacity. The bimodal form of the SWCC indicates the presence of two levels of pore sizes; namely macro pores and micro pores. For 10% and 15% SBR polymer and MICP process content, the macro pores are considered the dominant pore size covering a broad range of the SWCC from 0.1 to 100 kPa. Therefore, it is inferred that the SWCC of dune sand stabilized with SBR polymer and MICP process are strongly related to the texture and pore size distribution of the dune sand stabilized with SBR polymer and MICP process which in turn, has a significant impact on its hydraulic characteristics.
./files/site1/files/134/2.pdf

---

Introduction
Urban development and rapid extension of cities have been accompanied by a considerable growth in mechanized tunneling. The abrasivity of rock and even soil is a factor with considerable influence on the wear of tools. Soil abrasion and the resulting tool wear has a major impact on machine operation, utilization, and tunneling costs and time. One of the problematic aspects of working in abrasive grounds is the frequent need for the replacement of cutting tools, especially in pressurized face tunnel boring machines (TBMs). The effect of worn and damaged TBM cutter heads has been documented for numerous tunnel projects around the world. However, the lack of a standard or universally accepted test for soil abrasivity in geotechnical investigations has made the prediction of tool wear a difficult task.
Material and methods
A reliable prognosis of the abrasiveness of soils on a project would be of great benefit for designers, clients, and contractors. Many abrasion tests exist for rocks, and some have been proposed for soils; however, there is no universally accepted or international standard test for soil abrasivity testing. One of the most important and available tests in this field is LCPC abrasivity test which was developed by the Laboratoire Central des Ponts et Chaussées in the 1980’s. The LCPC Abrasivity Coefficient (ABR or LAC) can be used as a measure for both the abrasivity of the soil material and the influence of the grain size. The  abrasivity  testing  of  rock  is  controlled  by well-known parameters, whereas in soils many factors are influencing the abrasivity such as in-situ soil conditions, sedimentary petrology and technical   properties.
Tabriz metro line 2 Project about 22 km in length that will connect eastern part of the Tabriz city to its western part, considered as a case study. The project comprises a single tunnel which has been constructed using two earth pressure balance EPB-TBM with a cutting-wheel diameter of 9.49 m. In this study, based on geological and geotechnical properties, the tunnel route was divided into four parts and the abrasion and brittleness coefficients of alluviums determined by LCPC test. Besides that, the influences of some factors such as moisture content, mineralogy, grain size and shape, type and amount of foam have been studied.
Results and discussion
Based on more than 130 LCPC test results, in general, the Tabriz Metro’s line-2 route alluviums have the abrasion in the range of low to very high and the brittleness in the range of high to very high. In order to measure the effect of moisture content on abrasion and brittleness coefficient, the LCPC test was done on some samples related to the tunnel route in dried and moistened modes (5%, 0%, 15%, 20%, 25%, and 30%). Three types of sandstone, andesite, and conglomerate of the route were used to test the effect of moisture and petrology on abrasion. In a moisture range of 0 to 5%, in all types of materials, abrasion was increased. In a moisture range of 5 to 10%, abrasion was decreased in all three types, and this shows that a moisture level of 10% is a normal moisture content to create minimum abrasion. The behavior of sandstone and conglomerate is similar at higher moisture contents, and an increase in moisture content to 30% can increase abrasion of materials in both types. In conglomerate, abrasion at higher moisture levels is significantly more than in other modes. In andesite, an increase in moisture content to 20% can increase abrasion, although the abrasion is decreased with a moisture content of over 20%. In most samples, increase in moisture content led to decrease in brittleness of materials. In general, the highest abrasion level was related to conglomerate and the lowest level was related to sandstone. Moreover, andesite was at a lower level than conglomerate and a higher level than sandstone in terms of abrasion. Also, the results show that increased grain size led to increased abrasion, and the changes in andesite were greater than in sandstone.
In order to test the effectiveness of foam on abrasion, the foam used in workshops (A 168) made by Komeil Company Kashan was used for four types of petrography: conglomerate, andesite, sandstone, and silica. This test was conducted in the range of dried to 100 ml foam. In all types, decreased abrasion is observed from 0 to 20 ml and increased abrasion is observed from 20 to 100 ml.
Conclusion
The following conclusions are drawn from this research.
- With regard to the effect of grain size, increased size of grains could lead to more abrasion and less brittleness
- In terms of the effect of mineralogy, the conglomerate had the most effect on abrasion. In terms of brittleness, andesite was the most brittle.
- When the foam is moisturized in the sample, minimum abrasion is observed and above this level, the abrasion is increased.
./files/site1/files/134/4.pdf

---

One of the effective parameters in the dynamic behavior of reinforced soil walls is the fundamental vibration frequency. In this paper, analytical expressions for the first three natural frequencies of a geosynthetic reinforced soil wall are obtained in the 3D domain, using plate vibration theory and the energy method. The interaction between reinforced soil and the wall is also considered by modeling the soil and the reinforcement as axial springs. The in-depth transverse vibration mode-shapes, which were impossible to analyze via 2D modeling, are also analyzed by employing plate vibration theory. Different behaviors of soil and reinforcements in tension and compression are also considered for the first time in a 3D analytical investigation to achieve a more realistic result. The effect of different parameters on the natural frequencies of geosynthetic reinforced soil walls are investigated, including the soil to reinforcement stiffness ratio, reinforcement to wall stiffness ratio, reinforcement length, backfill width and length to height ratio of the wall, using the proposed analytical expressions. Finally, the results obtained from the analytical expressions proposed are compared with results from the finite element software Abaqus and other researchers’ results, showing that the proposed method has high accuracy. The proposed method will be a beginning of the 3D analytical modeling of reinforced soil walls.
 

---

Introduction
Drilling has various methods that from different aspects such as crushing mechanism, type of used energy etc., is divided to several types containing hand held drilling, percussive drilling, cable-tool drilling, rotary (or circular) drilling, percussive-rotary drilling and core drilling. Unlike the direct circulation drilling system (DC) in the reverse circulation drilling system (RC), the drilling fluid moves the annulus between borehole wall and the drilling pipe and comes back with the drilled pieces along inside the drilling pipe. The exploratory drilling system of RC by conducting powder samples with high purity and fast drilling rate, is a great help to the velocity and accurate of exploration of ore deposits. Samples produced in this method are in the form of soil and rock powdered and rock fragments of the drilled part, which may be dry or with little moisture. The air flow inside the cycle causes the collected powder sample to be often dry but sometimes is wet due to groundwater or drilling mud. Drilling is one of the most costly mining processes. Therefore, the most important goal in drilling engineering is to reduce costs, and the best possible decision to optimize the cost of drilling is to choose the best possible drilling method. Based on the field data, cost of drilling for each meter of a soft rock (e.g. travertine) by core drilling and direct drilling methods are about 3.3 and 1.2 times of the RC method, respectively. Also the cost of drilling, for each meter of a hard rock (e.g. granite) by core drilling and direct drilling methods are about 2.6 and 1.3 times of the RC method, respectively.
Materials and methods
In the present research, reverse circulation drilling (RC) has been compared with other important, common and practical drilling methods, such as direct circulation and core drilling methods in terms of various criteria containing drilling (time) rate, price (cost), type and quality of acquired samples and performance efficiency of drilling. Also, as a field study in this research, deep drilled boreholes with RC and core drilling methods in the gold mine of Khomein-Akhtarchi located in the Markazi province, were investigated and compared from different aspects. At the end, the ability to select the most appropriate drilling method among the variety of methods was studied. The study region is located at 25 km northeast of Khomein city in the Markazi province. This region consists of two exploration areas of Zarmadan-Akhtaran1 with the area of 13.21 square kilometers and Zarmadan-Akhtaran2 with the area of 2.85 square kilometers. Access to the Akhtarchi gold region is possible through the Khomein-Shahabiyeh (Goldsat)-Mahallat road. In the mining region, the Permian rock complexes include dolomite, dolomitic limestone from brown to dark gray, black Irony sandstone and white to milky limestone known as p^ds, p^dl and p^l units in the geological maps.
In the studied region, several deep boreholes, most of them by RC and some of them by core drilling methods have been drilled. In general, by now in the Akhtarchi gold zone in the Zarmadan-Akhtaran2 area 54 powder boreholes have been drilled through RC method called by RC1 to RC54. Also, there are 25 core drilling boreholes, 18 boreholes called by BH1 to BH18 in the Zarmadan-Akhtaran1 area and 5 boreholes called by BH1 to BH5 in the Zarmadan-Akhtaran2 area. During drilling operations, Permian and Cretaceous rock units have been encountered. The details of drilling via RC method for 4 boreholes with numbers 50, 51, 53 and 54 have been accurately taken. The measured drilling times were obtained from drilling personnel of the mine through the questionnaire which they were weighted mean if needed.
Results and discussion
The average drilling time for each meter of rock in boreholes 53 and 54 is 2:12 and 2:54 minutes, respectively. In both cases, the time duration is very short and this feature is one of the advantages of the RC drilling method. The longer average duration of drilling for each meter of rock in the borehole 54 than 53, is due to the depth of the borehole 54 and the hammer problem of the drilling machine during the drilling this borehole. In Table 1, the average duration of drilling operation per meter of rock in the Akhtarchi gold mine is given according to the type of rock (lithology) at definite depth intervals, on the basis of field studies. According to this table data, the duration of the drilling for each meter of rock in the greater depths increases that the reasons for increasing the duration of drilling for each meter of rock in greater depths are the difficulty of drilling due to the increasing length of rig, the reduction of transient energy to the bit, the probability of greater borehole declination, compaction increasing and as a result increasing the strength of rocks and more hydrostatic and lithostatic pressures in the great depths meanwhile at a great depth, the probability of capturing the drilling rig is too high. Also the cost (the time price) of drilling per meter of rock in this mine based on the dip and depth of drilling is about 1300 to 2000 thousand Rials by the RC method, against 2620 to 4250 thousand Rials by the core drilling method.
The results of the present research indicate that the RC drilling in comparison with other drilling methods, especially conventional and applied ones in terms of drilling costs and drilling rate (time) is highly desirable while is desirable regarding depth of drilling, the type and quality of the acquired samples and the overall efficiency of drilling performance. Although the core drilling method with the ability to drill very deep boreholes obtaining cores in terms of the type and quality of the acquired samples, as well as the depth of the drilling is the most desirable, but for exploration drilling (especially in the detailed exploration stages), deposits with low-grade and very little mineral indices (like gold mine of Khomein-Akhtarchi), and hence the large sample sizes are needed, employing RC drilling method having comparative advantages is economic.
Conclusion
Regarding the use of RC drilling method in the case study, the gold mine of Khomein-Akhtarchi, it was found that the RC method compared to the core drilling method, in terms of the duration of drilling operations or the speed of advance (the rate of penetration in the rock), drilling costs and efficiency of performance is desirable. Also, according to the type of mineral deposit (gold type), which is low-grade and the indices of the mineral are very low, therefore the large sample sizes are needed, thus, in terms of the type of obtained samples, employing RC drilling method in this case, is accounted a very important advantage related to the DC method (in terms of accuracy) and core drilling method (in terms of cost). The results of this research are useful for all users of drilling operations, including drilling engineers and technicians, engineering geology and geotechnical practitioners, mineral exploration engineers, groundwater aquifers and hydrocarbon reserves (oil and gas) to choose the optimal drilling method under different environmental and economic conditions based on criteria such as the purpose of drilling operations, costs, progress rate, type and quality of the yielded samples and the efficiency of drilling operation. Also, the use of RC drilling method has the advantages over the other drilling methods to be suggested for exploration of low-grade deposits such as gold, silver and copper, especially in the final stages such as detailed and mining exploration.
 

---

---

Introduction
The use of various additives to improve the properties of soils from past years have been studied by different researchers. Such additives are lime, cement, fly ash and fiber which have been used frequently in combination with soil. Lime is one of the oldest additives that it is utilized with different types of soils. Lime has positive impact on geotechnical properties of soil that alter some of the soil characteristics. Adding lime causes to reduce plasticity ranges, enhanced efficiency, strength and shrinkage of the soil. Extensive researches in the field of sustainability of clay with lime indicate that the optimum percentage of lime in the soil modification is between 1 to 3% by weight of the soil. But some researchers believe 8% by weight of lime are effective for soil stabilization. The presence of lime in clay soil yiels to occur some reaction, that it improves the soil properties. Reactions are included cation exchange flocculation, carbonation and pozzolanic reactions. Cation exchange between the clay cations and calcium cations takes place in lime. Cation exchange causes clay particles to get closer to each other creating complex structures in the clay soil and this improves the   clay soil features. In recent years the use of nanoparticles is considered in civil engineering field. The investigations have demonstrated that the use of nanomaterial increases cement reactivity and also improves density because it is filled with particles. Recent research has shown that the use of montmorillonite nano-clay soils to control swelling and to reduce failure potential in the soil. A number of researchers have expressed the use of nanoparticles causes to decrease the hydraulic conductivity of soils. In this paper, the effect of nano-clay and lime on the important soil parameters is evaluated. For this purpose, lime at 2 and 4 percentage and nano-clay at 0.5, 1 and 2 percentages have been added to clay soil and their impact on parameters such as optimized moisture, Atterberg limits, unconfined compressive strength and self-healing properties of soil is evaluated. Self-healing properties is one of the features, to repair damages due to internal erosion in the clay which is very efficient and important.
Materials and experimental methods
In the present research, the effect of lime and montmorillonite nano–clay to soil strength is evaluated. For this purpose, samples of clay soil (CL) has been used. In the experimental study, the percentages of additives mixed with the dry soil and then the optimum moisture and maximum specific weight of soil are determined with different percentages of additives. Soil Atterberg limits based on the ASTM D4318 standard have been determined.   Dry samples have been mixed together and then the water is added and mixed well with each other. Then the sample has been prepared in the form of a steel cylinder (cylindrical specimens) with a diameter of 50 mm and a height of 100 mm. Specimens were molded immediately and the weight and dimensions were carefully measured and then placed in plastic to prevent moisture loss and put them at 20 °c and 90%  moisture curing room.
Results and discussion
In this study, the percentage of lime is between 0, 2, 4 percent by weight and nanomaterials percentage is between 0.5 and 1 and 2 percent that can be varied in order to analyze the effect of various additives on the properties of the soil samples. The results indicate that increasing the nano-clay and lime percentage can enhance the optimum specific gravity of soil. The optimum moisture content of sample without any additive is equal to 19.5%. However, samples contain 2% nano-clay and 4% lime, the optimum moisture content increases to 23.5%. But the presence of lime reduces the maximum dry density of soil while adding nano-clay increases this amount. In samples with 4% lime and with no nano-clay, maximum dry density is 17  but in case of lime with 4% and nano-clay with 2% it is increased to 17.5 . In addition, adding lime without the presence of nano-clay only increases strength of soil. When 2 percent of lime is added, the strength of soil increases about 39 percent. As mentioned before, the effect of lime and nano-clay on increasing of unconfined compressive strength is almost the same which means by adding 2% of lime or nano-clay the strength of the soil increases about 40 percent. Using both lime and clay nanoparticles simultaneously (each 2%), a significant increase in strength of soil occurs in approximately 77 percent.
Conclusion
The use of nano-clay and lime improves soil strength parameters. But economically lime is more affordable than nano-clay. Therefore, if you need to increase only unconfined compressive strength, then the nano-clay is not recommended.
When it comes to self-healing in clay, the nano-clay can improve resistance rupture of the soil. By adding 2% of nano-clay in soil, healing of soil resistance after the break and after 24 hours can reach up to 60% of the ultimate strength of the soil. This property can be used to repair of locations that are subjected to internal erosion and scouring.
 
 

---

Introduction
The discussion of modeling the interaction of soil-pile groups due to a large number of parameters involved in is one of the complex topics and it has been one of the interests to researchers in recent years and has been dealt with in various ways. In recent years, the artificial neural network method has been used in many issues related to geotechnical engineering, including issues related to piles.. In this study, firstly it was tried to explain the importance of soil - structure interaction in calculating the dynamic response of bridges. Then, the effect of different effective parameters in calculating the interaction stiffness of the pile - soil group using artificial neural network was studied.  For this purpose, firstly, Sadr Bridge ( The intersection of Modarress and Kaveh Boulevard because the presence of tallest piers ) in the transverse direction, considering and without considering of the effect of soil - structure interaction was analyzed. The analysis was carried out in which the substructure soil was replaced with a set of springs and dashpots along the piles. Considering the fact that many factors are involved in determining the equivalent stiffness of springs, in the second stage, the effect of different factors on the stiffness of spring equations using artificial neural network was investigated. Finally, the artificial neural network method was used as a suitable method in order to estimate the equivalent stiffness values, the equivalent stiffness of the pile - soil group was introduced for different input values. equivalent stiffness of the substructure soil using the artificial neural network ,has not been used by researchers yet, so estimation of the optimal length and diameter of piles used in constructions and estimating the seismic performance of the bridge system after its implementation could be effective .
Material and methods
In this paper, spring-dashpot method is proposed to the non-uniform analysis of single-pier bridges which led to a 5-degree freedom model in the case of Sadr Bridge. This study also endeavors to investigate the SSI effect in dynamic analysis of bridges. This method is based on the traditional spring-dashpot method but in this method, non-linear stiffness is used along the piles, instead of linear stiffness and upgraded shape functions and coefficients are applied to make more precise mass, stiffness and damping matrices. Then the seismic responses of Sadr Bridge are compared in different conditions including or excluding the SSI effects. Considering the fact that in the present study to calculate the stiffness of the soil-pile group at depth, due to the effect of soil - structure interaction, the recommended method by API is used, the study of neural network analysis was used and the effect of different parameters used to determine the complexity of the soil-pile group system has been evaluated. The multi-layer feeder network, which has the most application in engineering issues, has an input layer, an output layer and one or more layers of hidden content, has been used for this purpose.  The best model of the neural network with a topology of 1-20-6 was provided using the hyperbolic sigmoid activation function, and the Levenberg Marquardt model and the training cycle 84, which had the least error mean square and the best regression coefficient. The effect of internal friction angle, soil density, pile diameter and the resistance per unit length has been evaluated with this method.
Results and discussion
[8] ارائه شده است صورت می پذیرد In this study, the importance of considering the effect of soil - structure interaction on the dynamic response of the Sadr Bridge was studied. Dynamic stiffness of the soil around the pile group was calculated based on the equivalent linear method and using the p-y springs. So, the effect of substructure soil was considered in dynamic analysis of the system . The artificial neural network was used to predict the stiffness of the soil - pile group, based on various input parameters and the stiffness sensitivity analysis of the calculated output values was conducted. In hard soils, the stiffness of the pile - soil group increases with increasing the diameter of the pile in the range of 1 to 1.5 m in diameter. However, in the range of 0.5 to 1 m in diameter, the diameter of the pile does not have much effect on the stiffness of the system and also stiffness decreases in the range of 1.5 to 2 m in diameter by increasing the pile diameter. Soil specific weight and angle of internal friction can change the system stiffness but the effect of the soil specific density is much greater on the stiffness of the soil-pile group system. Generally, the specific density in the range of 1000 to 2300 (kg/m³) will increase the stiffness of the system. In general, the ultimate strength of the soil among 100 to 550 (kN/m) affects the system stiffness. This effect within the ultimate strength between 100 and 220 (kN/m) causes increasing in the interaction stiffness value of the system and in the range of 220 to 550 (kN/m) causes reducing the stiffness of the system . The ultimate strength values ​​in a unit of length outside of the above range have little effect on the system interference stiffness. Despite the fact that the problem of calculating the soil - pile interaction stiffness is a direct solution, the use of the proposed neural network model can help in predicting optimal values ​​of diameter and length of the pile to achieve maximum soil- pile stiffness and especially for long bridges it will has a significant impact on reducing cost and seismic design of the bridge.
Conclusion
The results of this study are as follows:
The results showed that considering the interaction effect, although it increases the relative displacement of the deck, reduces the maximum base shear and moment. This suggests that considering the maximum base shear and moment in the interaction conditions may not lead to a seismic design for certainty, although closer to reality.
Artificial neural network is an efficient way and new method to predict the stiffness of the soil-pile group system based on different input values that have not been used yet. So that with the physical and mechanical properties of the soil as well as the geometric properties of the piles, it is possible to predict the interaction stiffness values with the proper precision.
According to the results and diagrams obtained from the neural network model, which are mainly sinusoidal, the optimal values ​​of the interaction stiffness can be obtained by obtaining the pile diameter, specific gravity, the internal soil friction soil to achieve optimal interaction strength. It is also possible for each site to estimate the depth of the piles in order to achieve optimal hardness. 
./files/site1/files/142/4Extended_Abstracts.pdf

---

Introduction
Solid waste is one of the unavoidable products of every society that necessitates the establishment of municipal solid waste management system. Because of variability in quantity and composition of municipal solid wastes, several management scenarios are considered. Assessing the environmental impacts of the life cycle of these scenarios will have a significant role in reducing and resolving urban service management problems. The aim of this study was to compare different scenarios of municipal solid waste management in Sirjan city using life cycle assessment (LCA) approach. LCA methodology is used to evaluate the environmental performance of the waste management of Sirjan for different scenarios, according to the ISO standards 14040 series 2006.
Material and methods
After identifying the quantitative and qualitative characteristics of the produced wastes within the scope of the study, the quadratic steps of the LCA method are followed in relation to each of the scenarios. The stages of life cycle assessment in the present research are as follows:
 1. Determining goals and scope: Our goal is to compare environmental impacts of scenarios that include different methods of disposal. The boundaries of the study start from the collection of municipal solid wastes from the transfer station and ends with the final disposal of waste (Figure 1)

Figure 1. System boundary
Four scenarios have been investigated and evaluated in the environmental field (Table 1).
Table 1. Disposal solid waste scenarios

Scenario	Compost (%)	Recycle (%)	Incineration (%)	Landfill (%)
1 2 3 4	0 68.4 17.1 0	0 19.2 15 19.2	0 0 55.9 69.8	100 12.4 12 11

2. Collecting data and life cycle inventory (LCI): Various tools have been developed for LCI, one of which is the IWM-2 model. The IWM-2 model is one of the lifecycle assessment models that can be used to define different scenarios and then to compare the environmental impacts of each scenario. At this stage, the data from physical analysis, the amount of waste produced, the stages of separation at source, collection, transportation and final disposal, were collected and analyzed and the amount of contamination caused by each of the scenarios and energy consumption were determined.
3. Life cycle impacts assessment (LCIA): Assessing the impacts of the life cycle is a step of life cycle assessment, aimed at understanding and assessing the magnitude and significance of the potential environmental impacts of a product or service. At this step, the various information and data obtained at the LCI stage are reduced to less indicators and impact categories in order to facilitate the interpretation of this information and provide clearer outcomes to decision makers and managers. In this step, input data are allocated to the five impact categories of energy consumption, greenhouse gases, acid gases, photochemical gases and toxic emissions.
4. Interpretation of results: At this stage, the results of the LCI and LCIA will be evaluated so that the stages or points which have the greatest and least harmful impacts on the environment in the production and consumption of the product have been determined. Finally, conclusions and solutions are explained.
Results and discussion
Results of the model were allocated to five categories consisting of energy consumption, greenhouse gases, acid gases, photochemical gases and toxic emissions. In every category, the ecological index as a quantitative measure to compare scenarios was calculated.
Conclusion
In this study, the life cycle assessment approach was used as a decision tool for choosing the appropriate waste disposal scenario in Sirjan city. The second scenario (68.4% compost, 19.2% recycling, 12.4% landfill) was selected as the preferred option for municipal waste disposal in Sirjan city. Also the results of this study show that in an integrated municipal waste management system, increasing the rate of separation and recycling will significantly reduce the release of environmental pollutants../files/site1/files/142/5.pdf
 

---

Introduction
Improving the geotechnical characteristics of soils including superficial or deep soils has always been a challenge to geotechnical engineers. Therefore, various physical and chemical methods are used to improve different types of soils. In general, any physical, chemical, biological or combination of methods are used to change the characteristics of natural soil mass in order to achieve engineering goals which is defined in the "soil stabilization." Among different types of additives for soil stabilization, the use of pozzolans has been investigated by researchers because of their chemical compatibility with the environment and the cementation products due to chemical reactions. Todays, a lot of researches has been done on the use of natural or artificial zeolites as pozzolanic materials for the production of cement mixtures. This material, as a pozzolan, increases the speed of the pozzolanic reactions and reduces the density of cement products. However, many studies have been done to investigate the effect of zeolite and sepiolite on the resistance of cement products such as concrete, but so far, the use of these additives has been less considered for soil improvement. On the other hand, because of the compatibility of zeolite and sepiolite with the environment and their unique physiochemical properties, it is necessary to pay attention to these additives in order to improve the soil. Therefore, in this research, the effect of zeolite and sepillot additives with different percentages at different treatment times have been investigated to determine the elasticity modulus and hydraulic conductivity with focus on soil microstructure behavior.
Materials and methods
1. The properties of the soils
In this research, two types of soil including clayey sand (with 20% clay) and sandy clay (with 51% of clay) were used. The studied soils were a mixture of clay and sand of Firoozkouh (a typical type of sand located in north of Iran). Some physiochemical properties of zeolite and sepiolite are presented in Table 1.
Table 1. Physiochemical properties of zeolite and sepiolite used in this study

L.O.I.	Na2O	K2O	MgO	CaO	Fe2O3	Al2O3	SiO2		Chemical component
25.11	0.02	0.01	15.73	0.01	o.61	0.3	55.3		Sepiolite (%)S
11.94	0.13	-	0.87	2.45	1.26	13.54	69.74		Zeolite (%)

2. Experiments
The uniaxial compressive strength tests were performed at 0.1 mm/min according to ASTM D2166 standard. The stabilized soil samples were compacted at percentages of 0, 5, 10, 15, 20 and 25 in cylindrical molds (38mm × 76mm) in five layers to achieve the desired density. In order to investigate the effect of curing time, the samples were placed inside sealed containers and underwent the test at instantaneous, 7, 14, and 28 days and at the desired additive percentages. To investigate the effect of additives on the soil hydraulic conductivity, clayey sand soil with additives 5, 10, 15, 20, and 25% was prepared using dry mixing method. Then, the prepared mixture was poured from a specific height into the permeability mold with a height of 8.65 cm and diameter of 5 cm. In this way, the specific dry unit weight of all samples was obtained as 1.47 g/cm³, close to the minimum specific dry unit weight. In this research, concerning the considerable effect of fine-grained soils on hydraulic conductivity, falling head test was used to determine the permeability coefficient.
In order to the morphology of the clayey sand soil without additives and stabilized with additives 15% was examined through SEM test.
Discussion and results
1. Modulus of elasticity
In this study, after uniaxial tests in different percentages and ages, the stress-strain graphs were plotted and then the elasticity modulus was calculated. The results showed that, with increasing zeolite content, the modulus of elasticity has been increased and, with increasing curing time, except for a slight decrease, after 7 days, the modulus of elasticity increased. During the initial treatment (7 days), the hardness of the sandy clay soil decreased and then increased with increasing time. In general, hardness in both soils in the high percentages of zeolite is significantly is increased.
Also, the effect of sepiolite on the modulus of elasticity has been studied. The results indicate that with the increase in the percentage of additive and lengthening the curing time, the modulus of elasticity is increased. This increase in the stabilization of both sandy clay and clayey sand soil is almost the same. In addition, in the case of sepiolite modification, the elasticity of sandy clay and clayey sand is approximately equal to 5 times in comparison to the initial value of unstabilized soil. However, in zeolite, the modulus of elasticity in clayey sand soils is almost 2 times, and sandy clay is nearly 5 times higher.
2. Permeability
To investigate the effect of additives on the soil hydraulic conductivity, clayey sand soil with additives 5, 10, 15, 20, and 25% was prepared using dry mixing method. The samples were saturated in a short period and permeability test was carried out immediately. Permeability coefficient changes were mostly influenced by physical factors. Therefore, due to the fineness of both types of additives, the hydraulic conductivity decreases with increasing additive content. The amount of reduced hydraulic conductivity in sepiolite stabilization is greater than zeolite due to the structure of the sepiolite (fiber-shaped) compared to zeolite.
 
 
3. SEM imaging
In this study, attempts were made to examine the reasons behind the obtained results more carefully through SEM imaging.

c                                     b                              a
Figure 1. SEM image of non-stabilized clayey sand soil (a) soil stabilized with zeolite 15% (b) soil stabilized with sepiolite 15% (c) during the curing time of 28 days at magnifications 10000X
Figure 1a displays the SEM image of non-stabilized clayey sand soil. As can be seen in the figure, the soil structure is clear as layered and clay scales can be seen as laminated. Figure 1b demonstrates the SEM images of clayey sand soil stabilized with zeolite 15% during the curing time of 28 days. The sample has lost its layered structure in response to stabilization with zeolite during the curing time and changed into an integrated structure. This can be due to incidence of chemical reactions such as ion exchange and pozzolanic reactions in response to adding zeolite. Figure 1c demonstrates the SEM images of clayey sand soil stabilized with sepiolite 15% during the curing time of 28 days. As shown in the figure, the sepiolite has a fibrous-shaped structure that is longitudinally twisted. Also, with  curing time increase, complex structures have emerged that could be due to the occurrence of chemical reactions.
Conclusion
This study examined the effect of zeolite and sepiolite additives on strength parameter of clayey soils. Accordingly, uniaxial compressive strength test was performed on clayey sand and sandy clay soil at percentages of 0, 5, 10, 15, 20 and 25% of zeolite and sepiolite with instantaneous curing times of 7, 14 and 28 days. Further, permeability test was conducted at different percentages on stabilized clayey sand soil. Also, to investigate the effect of these materials on soil microstructure, SEM imaging was performed at 28 days. The results show that both additives increase the elastic modulus of clayey sand and sandy clay soils. Also, the results indicate a steady increase in the stiffness of the cured soil with sepiolite during processing time. However, reducing soil hardness can be seen in stabilizing with zeolite at lower rates and lower percentages. In permeability test, hydraulic conductivity decreases with increasing additive content. The rate of permeability reduction in sepiolite is higher than zeolite. SEM images show that chemical reactions create an integrated structure that ultimately increases uniaxial compressive strength and modulus of elasticity. Also, SEM imaging depicts physical changes along chemical reaction in soil stabilized with sepiolite. Ultimately, increasing soil strength resulting from additive alongside environmentally friendliness is recommended in superficial and deep improvement of soil../files/site1/files/144/Rajabi.pdf
 

---

Introduction
Shallow tunnels have a vital role in urban planning, railway and highway transportation lines. The presence of underground cavities can leads to stress concentration and consequently, instability of the spaces against static and especially dynamic loads. Therefore, the aim of this study was to evaluate the effect of elliptical cavity and its inclination on sandstone rock behavior under compressive static and tensile dynamic loads. In order to evaluate the effect of the cavity under static stress conditions, two groups of intact and hole-bearing sandstone cores with 0, 30, 60, and 90 degrees of hole inclination were prepared and tested under uniaxial compressive loading test. During the test, in addition to the stress recording, damage and deformability of the samples were recorded by using the strain gauge, acoustic emission sensor and camera. Split Hopkinson pressure bar (SHPB) test apparatus was used for doing dynamic loading test. Furthermore, the damage process was recorded using a high-speed camera with 10 micro-seconds interval of frame capability. The obtained results showed that presence of the cavity reduced the rock strength in maximum state (θ=0) up to 55% and in minimum state (θ=90) up to 77% of its initial uniaxial compressive strength. Dynamic tensile loading tests illustrate that the elliptical hole near the free end of sample (reflection boundary of compressive wave to tensile wave) is stable due to locating in superposition area, while the other cavity out of the area with each inclination was undergone to spalling failure. Assessment of failure surface using scanning electron microscope and thin section study indicates that the dominant fracture is grain-boundary type and iron oxide cement has a vital role in developing of this type of fracture.
 


 

---

A jointed rock mass presents a more complex design problem than the other rock masses. The complexity arises from the number (greater than two) of joint sets which define the degree of discontinuity of medium.  The condition that arises in these types of rock masses is the generation of discrete rock blocks, of various geometries. They defined by the natural fracture surfaces and the excavation surface. Stability problems in blocky jointed rock are generally associated with gravity falls of blocks from the roof and sidewalls. Whereas for block defined in the crown of tunnel,the requirement is to examine the potential for displacement of each block under the influence of the surface tractions arising from the local stress field and the gravitational load, in this paper various types of wedge formation in the crown of tunnel due to intersection of joint sets with various dip were examined. The state of stability of the wedge was then assessed through the factor of safety against roof failure. Following that the formed wedges in New York city and Washington D.C tunnels crown were investigated with limiting equilibrium analytical method and by use of Hoek and Brown failure criterion. The obtained results from analytical method corresponded with field observation.
 

---

In Yazd Darreh-Zereshk copper deposit geophysical data containing magnetic, resistivity and induced polarization have been surveyed and 25 boreholes have been drilled in the area. In the present research, inversion and processing of geophysical data as well as their qualitative and quantitative accordance with boreholes assay data have been carried out. To achieve the goal first, total magnetic intensity map after applying necessary filters and processing, was mapped to identify surface and deep expansion of anomalies on it. Drawing the anomaly profile of magnetic stations surveyed along 4 geoelectric profiles shows that most of the magnetic anomaly zones have high chargeability and low resistivity that indicates the qualitative compatibility of magnetic and geoelectric data, as a result increasing the probability of mineralization in the area. Afterward  on the basis of qualitative interpretation of geoelectrical sections, optimal locations of drilling on the each profile were proposed. Plotting mineral deposit cross-section along the geoelectrical profiles using the boreholes assay data, revealed that drilling of some boreholes located on the geophysical profiles haven’t been based on the results of geophysical operation, carried out without any right logic, purpose and design. In general, the qualitative accordance of the results of geoelectrical operation with the boreholes assay data showed a pretty good qualitative accordance. Also investigation of linear correlation coefficient value between inverted geophysical data and borehole assay in a specific same range after a same definite gridding and interpolation of their values, overall indicated a relatively good quantitative accordance (between 0.4 and 0.7)../files/site1/files/151/1.pdf

---

Safety design of structures concerning surface faulting effects such as shear and differential subsidence are very costly and in some cases are impossible. Then the appropriate approach for encountering surface faulting is to determine a suitable fault-avoidance zone. In this study, firstly the theorem of avoidance fault zone is presented, and then the setback area from the fault zone of South Mashhad fault is proposed. Recent studies show that South Mashhad fault is a right-lateral strike-slip fault with a normal component that cut the Quaternary sediments. In this work, the average slip rate and estimated return period for South Mashhad fault are 0.59 mm/yr and 2930 years, respectively.  Accordingly, the proposed avoidance zones in the south (hanging-wall) and north (foot-wall) of the fault are 80 and 70 meters, respectively. Considering the avoidance zones, many residential and other important structures are located in the avoidance zone of the South Mashhad fault../files/site1/files/152/%D8%AD%D8%A7%D9%81%D8%B8%DB%8C.pdf
 

 

---

The soil of the Arvand free zone in the north of Khorramshahr is fine cohesive and cannot be used in earth works. On the other hand, suitable materials for this purpose (coarse-grained soils) are located at the farther distances which a considerable cost requires. In this regard, it is trying to improve the soil with lime and furnace steel slag. This study is focused on improvement of the fine-grained soil by adding various contents of lime and furnace steel slag. For this purpose, after sampling and performance of compaction tests, different amounts of slag (10, 20 and 30% by weight of dry soil) and lime (2, 4 and 6% by weight of dry soil) were added to the soil and after curing for 28 days, the effect of additives on the physical and mechanical properties of soil was investigated by using several tests such as Atterberg limits, compaction, uniaxial compressive strength (UCS) and CBR as soaked and unsoaked. Based on USCS classification the study soil is CL, its plasticity index is about 25% and sulphate ion content is more than 0.5%. Experimental results show that by adding slag and lime at different contents to soil, mechanical properties of soil improve dramatically, so plastic index of soil decreased and UCS and CBR has been increased. Also, the maximum dry unit weight of soil increases and the optimum moisture content decreases. The test results also indicate that the effect of lime on soil is higher than slag and the effect of slag for less than 35% is not considerable, however the test result of unsoaked CBR show that the bearing of soil increase in the more than slag content 20% is significant. According to the previous studies, due to the relatively high sulphate ion content in the soil, the use of lime alone is inappropriate and the slag can only physically improve soil conditions but also chemically prevent the formation of large volume minerals (like Ettringite) by the reaction of lime with soil sulphate ion../files/site1/files/152/%D8%AD%D8%B3%DB%8C%D9%86_%D8%B2%D8%A7%D8%AF%D9%87.pdf

---

Existence of sodium elements in fine-grained of some soils causes dispersive phenomenon in them.  Failure to accurately identify dispersive clays leads to damage because dispersive clay soil particles disperse under certain conditions and wash away quickly. This research assesses dispersive degree of outcropped soils in southeast of Yazd. Finally, the modification of soil dispersive potential was investigated by using nanocellulose.  After performing a series of physical, chemical and mechanical tests, characterization/ specification of the studied soils were determined. Then dispersive degree was specified by conducting chemical, pin hole, crumb and double hydrometer tests. Finally, soil dispersivity stabilization was performed using sample preparation with 0.5, 1 and 1.5% nanocellulose. The results showed that the studied soils have moderate dispersive in borehole A and extreme to slightly dispersive in borehole B. Therefore, it can be concluded that the closer we get to the center of the plain, the greater the dispersibility. The results of the dispersibility stabilization soil tests indicate that the optimum moisture content and dry specific gravity increases and decreases. Uniaxial strength and CBR increases. Also, it shows that the increase in nanocellulose has a positive effect on the modified samples and improves the soil dispersibility in this area../files/site1/files/152/%D8%B2%D8%A7%D8%B1%D8%B9.pdf
 

---

In current paper the effects of surface unreinforced / reinforced sand layers coupled with and without single and group sand columns on the bearing capacity – settlement behavior of soft clays has been investigated. In this regard behavior of soft clay, clay + unreinforced / reinforced sand layer, clay + single / group sand piles and clay + unreinforced / reinforced sand layer + single / group piles samples has been assessed. Geogrid was adopted as the reinforcement, a circular plate 5cm in diameter as the loading surface and C.B.R. apparatus as the loading system. Results show that employing unreinforced / reinforced sand layers at a settlement ratio of 5% improves bearing capacity by 4 t0 7 times the soft clay. Coupling the surface unreinforced / reinforced sand layers with single / group sand piles further increases the bearing capacity by 7 to 9 times that of soft clay.

./files/site1/files/%D8%B9%D8%A8%D8%AF%DB%8C.pdf
 

---

Extended Abstract

---

---

---