Search published articles


Showing 3 results for Numerical Simulation

Ahmadzadeh, R Bagherpour, Saeed Mahdevari,
Volume 10, Issue 2 (11-2016)
Abstract

Because most part of Iran country is located in a dry climate, construction of water conveyance tunnels is inevitable. One of the major challenges in the construction of these tunnels is inflow of water into the tunnel during the construction and operation phase. The Rozieh water conveyance tunnel whose length is 3200 meters is a part of water conveyance project to the Semnan city and it is located 30 k NE of Semnan city. In accordance with the drilled boreholes, the tunnel route has been classified into eight zones from the geotechnical view. Then the permeability coefficients of host rock were calculated using back analysis approach on the basis of numerical simulation results and water inflow quantity during the construction phase. A parametric study was done on the lining and cement injection zone permeability and the thickness of cement injection zone. According to this study, the effect of injection zone thickness variation on the water inflow quantity is negligible. So with the assumption of 3 meters thickness for the injection zone, the permeability coefficient of host rock after injection were evaluated. Dependent on the initial rock permeability, cement injection could reduce the rock permeability 10 to 1000 times. In addition, the water inflow into the tunnel was calculated using hydro-mechanical coupling analysis. According to this analysis, the water inflow calculated by the hydro-mechanical coupling analysis is 50 to 70 percent less than the hydraulic analysis.


Ehsan Taherabadi Eliyas, ,
Volume 13, Issue 5 (12-2019)
Abstract

This paper investigates the effect of micropile installation into saturated sandy soil by means of finite element method. The obtained results from numerical modeling are compared with the received data from the site. The validation of software has been done by simulating standard penetration test. The effect of some changes in spacing (3m, 1.6m and 0.8m) and injection pressure (1cm, 2.5cm, 5cm and 10cm boundary displacement) micropiles on liquefaction behavior was discussed. The results show that numerical modeling presented a conservative conclusion about the potential of liquefaction. The modification of soil increased by increasing injection pressure of grout. Also, it was observed that the effect of micropile spacing has less impact than the injection pressures up to 1m free distance of micropiles. Then for closer micropiles, the effect of spacing and the effect of pressure became bold and intensive, respectively. Because of direct relationship between number of SPT and liquefaction potential, it would be necessary to simulate SPT and to validate with the real data, before and next of micropile installation. This approach can be a proper way of forecasting the efficiency degree of modification by micropiles and could save costs and time.

Mrs Roya Masoumipour, Dr. Saeed Mahdavi,
Volume 19, Issue 1 (6-2025)
Abstract

The Chador-Malu open-pit mine is faces complex challenges regarding the long-term stability of its slopes. These are directly influenced by time, environmental changes, and stresses induced by mining activities. Considering the existing evidence of potential future instability, displacement changes along the northern to eastern pit walls were analyzed over an 18-month period. Long-term wall displacements were measured using radar. Through back-analysis and three-dimensional numerical simulations, the equivalent creep behavior of the slopes was evaluated using the Maxwell creep model. After assessing the geomechanical parameters, the impact of three scenarios  passage of time, bench widening, and pit deepening  on slope stability was investigated under three horizontal-to-vertical stress ratios of 0.5, 1, and 1.5. The analysis results indicated that a horizontal-to-vertical stress ratio of 1.5 better matched the field observations. In the first scenario, a 50% increase in time led to over a 100% increase in displacement rates, indicating a rise in instability potential over time. In the second scenario, unloading the first two benches reduces the instability potential, due to an 18% reduction in uplift while unloading up to the eighth bench increased instability potential due to the reduction of weight at the slide’s toe and an increase in the average uplift. In the third scenario, pit deepening formed another sliding zone between the tenth and seventeenth benches.


Page 1 from 1     

© 2025 CC BY-NC 4.0 | Journal of Engineering Geology

Designed & Developed by : Yektaweb